Marca: Others

Tienda: RC-Fever.com

Disponibilidad: En almacén, envío inmediato.

This is the Remzibi OSD module with GPS module. Functionality : Easy PC connection for configuration/calibration purposes using dedicated PC program (HappyKillmore's exelent work) No RC channel occupation for proper work in air GPS detection and configuration automatically (configuration commands fully editable) Auto "save home" function configurable , depends of sat number , button "save home" works independently Metric(km/h) or feet(mil/h) units - configurable Zero altitude to airfield level - configurable (absolute or relative) Fully configurable screen layout Graphical symbols and fonts configurable (possible exotic languages , fully editable font table) Voltages calibration function and all ADC inputs including alarms Frequency calibration for Hz or RPM Information can be displayed on the screen: Latitude (format DDMM.MMMM or DD.DDDDDD can be selected) Longitude (format DDMM.MMMM or DD.DDDDDD can be selected) Speed (k/m or miles/h can be selected) Altitude (meters or feet) To-home course (animated arrow or whatever else animation definable by user) To-home distance (meters or feet) Satellite quantity Video battery voltage (individually scaled and calibrated) Main battery voltage (individually scaled and calibrated) Flight timer Variometer (meters/s or feet/s) UTC Time UTC Date Alarms for distance , ADC , altitude , battery voltages (individually scaled and calibrated) 32 static displayed independent graphical-character symbols , configurable After detection 0 speed for configurable X seconds , shows maximal values for altitude , distance , speed , function can be switched off 6 ADC channels to use with any additional sensors , each ca be individually calibrate and alarm set , cooperate with any additional sensors (optionally scaled by opamp or resistor dividers) with analog output (RSSI , air pressure, current sensor , temperature , whatever else with analog output) , display format as 123 or 123.4 can be selected Frequency meter (RCl input resistor need 220-515ohm or T0 in new board) - can be scaled for any units by gain as Hz or RPM , cooperate with magnetic(hallotron) or optical sensor - or can be used as frames counter when connected to RX output directly OSD have support for $M custom messages - for those who want to display his own text or fonts(graphics) anywhere at display , $M can be transmitted between $GPGGA and $GPRMC GPS strings by "your device" Since 1_77 firmware GPS configuration support MTK as strings and Ublox as binary GPS modules Every displayed information can be placed everywhere on screen layout , can be on or off , has definable leading character(or picture) and ending character(or picture) Button function Save home position (short click) (work only when GPS is detected) Video mode change (NTSC or PAL) press and hold button for about 1 second (work only when GPS is detected) Configuration mode (pressed and hold button then connect power and relese button , font pattern on screen will appear) for USB communicate OSD Technical data : Supply power : 7V-14V (ex. lipol 2S - 3S) Video voltage measurement range 0-15V Engine(ENG) voltage measurement range 0-30V General purpose ADC measurement range - any range depended from resistor dividers or used opamps . Video signals - standard PAL or NTSC (both working very well) GPS - any GPS 5V supply with NMEA protocol with TLL standard TX RX signals (however best results and advantages are with dedicated GPS module working 5Hz update position) Weight : 16 gram (OSD + dedicated GPS) Printed board size 20mmx45mm GPS Connection : TTL, 3.3V/5V Compatible Receiver: 50Channels, GPS L1 (1575.42Mhz) Locating Accuracy: 2.5 mCEP (SBAS: 2.0mCEP) Updating Speed: Max. 5Hz Capture Duration: Cold start: 27S (fastest), Warm start: 27S, Hot start: 1S Capture sensitivity: -161dBm Signal type: NMEA (default) / UBX Binary Remzibi OSD Module x 1 GPS Module x 1 Connecting Wires x 1 Set